Search

Noise pollution is a workplace hazard which causes loss of hearing, depending on the sound pressure level and duration of exposure. Because duration of exposure is usually uncontrollable, sound absorbers are used to reduce the value of sound pressure level. A common method to reduce noise is to use porous sound absorbers made out of mineral wools or glass fibres. However, these materials pose health risks and are non-recyclable. This project aimed to fabricate a sound absorber using recycled paper which is in the form of egg cartons as an alternative to the abovementioned fibres. Paper fibres posses high fibre porosity and can be manufactured in a manner which the properties can be easily controlled, making them ideal to be made into sound absorbers. Furthermore, they are biodegradable, do not pose health risks and can be manufactured into different shapes easily. Recycled paper was first turned into pulp, blended and poured into moulds. Different amounts of pulp was compressed until the sample size was approximately 20 mm thick and then dried in a furnace dryer at 600C for 12 hours. The samples were tested using a two-microphone, transfer function impedance tubes according to the ISO 10534-2 standard. Its porosity was determined using a modified wash basin method. The results indicate that the optimum panel has an average noise reduction coefficient, (NRC) of 0.50, which qualifies it to be used as a sound absorbing material. It also encounters its maximum value of 0.98 which occurred at the 1575-1675 Hz range. When compared to other materials, recycled paper has similar properties as coir fibre and is quite comparable to other commercial sound absorbers at the same thickness.

Universiti Putra Malaysia (UPM) tyre traction testing facility was designed and developed to spearhead fundamental research on traction mechanics with high-lug agricultural tyres on tropical soils. This available facility consists of a moving carriage with a cantilever-mounted tyre that moves in either forward or reverse directions on rails well above a soil tank. The present facility set-up was able to operate in either: (a) towing test mode for tyre motion resistance studies, or (b) driving test mode for tyre net traction and tractive efficiency studies. The test tyre on the moving carriage under the towing test mode was made to rotate and engage onto the soil surface in the tank through a chain drive system. Under the driving test mode, the test tyre on the moving carriage was powered to rotate by a motor and a gearbox system with an additional pull provided by a cable-pulley mechanism connected to a tower with hanging dead weights. All controls on the moving carriage were activated from the main control console. Respective transducers were positioned at various localities within and interfaced to a data acquisition system to measure tyre horizontal and vertical forces, tyre sinkage, tyre speed and motion carriage speed. The data acquisition system was able to receive the measured signals in real time, display on the monitor screen and record into its CPU storage memory. Static calibration tests on various associated transducers showed excellent linearity with coefficients of determination ( r 2 ) of close to 1. The developed facility was successfully tested to determine motion resistance and net traction ratios for high-lug agricultural tyre at the recommended inflation pressure on sandy clay loam soil.

A study was conducted to determine the accuracy of Wismer-Luth and Brixius equations in predicting net traction ratio of a high-lug agricultural tyre. The tyre was tested on a sandy clay loam soil in an indoor University Putra Malaysia (UPM) tyre traction testing facility. The experiment was conducted by running the tyre in driving mode. A total of 126 test runs were conducted in a combination consisting of three selected inflation pressures (i.e., 166, 193 and 221 kPa) and two wheel numerics (i.e., 19 and 29) representing two extreme types of soil strength under different levels of travel reduction ranging between 0% and 40%. Regression analysis was conducted to determine the prediction equation describing the tyre torque ratio. Marqurdt’s method used by Wismer-Luth for predicting non-linear equation was not found suitable in predicting the torque ratio of the test tyre awing its low coefficient of determination and inadequacy. The logarithmic model was found suitable in torque ration prediction. From analysis of covariance (ANCOVA) the mean effect of travel speed, tyre inflation pressure and wheel numeric on tyre net traction ratio were found to be highly significant, while the interaction of inflation pressure and wheel numeric was not significant. The 193 kPa inflation pressure was found the best, among the three inflation pressures used, in getting higher net traction ratio and higher maximum efficiency. Finally, two models were formulated for tyre net traction ratio; one in terms of wheel numeric and travel speed reduction and the other in terms of mobility number and travel reduction, to describe the tested tyre performance at different soil strengths.

A single wheel tyre facility at University Putra Malaysia (UPM) was used to check the validity of Wismer–Luth and Brixius equations in predicting the motion resistance ratio of a high-lug agricultural tyre and to investigate the effect of inflation pressure. A Bridgestone 5-12, 4 ply, lug M was tested on sandy-clay-loam soil. The experiments were conducted by running the tyre in towing mode. Three inflation pressures (i.e., 166, 193 and 221 kPa) were investigated and wheel numerics ranging between 0 and 70. The analysis of covariance (ANCOVA) revealed that both inflation pressure and wheel numeric have significant effects on tyre motion resistance ratio. Regression analysis was also conducted to determine the closeness of fit for Wismer–Luth’s and Brixius’ equations in predicting the motion resistance ratio of the tested tyre. Finally, three new logarithmic models for tyre motion resistance were formulated. The advantage of reducing tyre inflation pressure from 221 (nominal pressure) to 193 kPa on the motion resistance ratio of the high-lug agricultural tyre was pronounced. However, the tyre’s motion resistance ratio deteriorated with further reduction in tyre inflation pressure from 221 (nominal pressure) to 166 kPa.